The longer the soaking time, the higher the chance of failure, such as sudden engine shutdown at high speeds, airbags can not pop up at critical moments or even cause the pop-up, etc., Amoy car network to remind you to identify the bubble truck can open the floor to see if the moldy corner , long hair, feel whether the seat expansion, deformation, observe whether there is water vapor in the dashboard, the car roof and door trim panel is yellow. In addition, you can also write down the frame number of the vehicle and call the 4S shop or insurance company to learn more about the vehicle maintenance records and the claims settlement. Â The hazards of swill trucks mainly include the following aspects: (1) Circuit system, engine power system, cabin odor, etc. (2) Dirty water and harmful substances increase the speed of oxidation in various aspects of vehicles, shorten the service life of vehicles, and present potential safety hazards. (3) The circuit system is significantly affected. Such as SRS, ABS, EBD, TCS and other high-tech electronic aids, after soaking, basically no longer work properly. So how do you identify this car is a bubble car, from which details can be noticed? The next point can be used as a reference. 1, see the price Cars that have been soaked in water will have a 20% downward rate in price compared to the equivalent model, and used cars that are too cheap should be kept in mind. 2, see the body details (1) Engine compartment: Whether the engine compartment is dirty or not, sediment-like stains are attached to the water tank in the engine compartment, cold air cooling fins, and small lenses for the front panel of the water tank (see from bottom to top). Amoy car network reminds you to also pay attention to the engine next to the small parts, generators, starter motors, power outlets, left and right wheel rail seams. It is also important that the engine looks new if it is blistered (because it has been cleaned). (2) Engine support frame: The nut of the engine support frame is screwed off because the engine is to be removed and repaired. (3) Engine block: The nuts on the engine block are screwed in because the engine is overhauled. (4) Center console: From the foot space in the front row to the center console, sludge and deposits of dirt and dirt on the lines and other components are attached to the surface. (5) Interior part: Front and rear seat (back) Check the spring and the inner set of brown cloth moldy smell of residual sludge, remove the door trim, from the car with a small lens from the bottom up Sludge (not washed in the car washing machine) is digged by front and rear windshield rubber tools. The sludge is the water squeezing car, and the water level exceeds the engine cover. The center pillar of the front and rear doors (with plastic cover plate cover) Live) Can be clamped open with a screwdriver, and there is a darker color in the place where there is a lot of water in the mud, indicating the height of the car. (6) Ground glue: The corners of the ground glue can obviously be seen to be relatively soft, damp and smelly. (7) Engine sound: The engine sounds relatively loud and slightly unstable. (8) Test run, feel gearbox: During the test run, the gearbox can be found to be able to shift normally, but it is particularly jerky. If these conditions exist and the vehicle has no signs of accident, it can be confirmed as a bubble truck. The value of vehicles after flooding is greatly reduced, especially for high-end vehicles. Because the engine of the bubble truck usually requires overhaul, Amoy.com believes this is not the main problem. The key is that the circuit part of the vehicle enters the water, especially after each control computer version is flooded, it is easy to short-circuit, burn, and rot. In the future, there will often be failures.
there will be about 35% carbon black residual from tyre pyrolysis machines
it could be sold directly or refined into better quality ones.
say N330 or N660
it could be widely used for additives
say rubbers for playground, for car tyres, or shoes etc.
usually there are models with capacities from 1-20tons per hour
Working Principle
The grinding Process of the Main Mill is that the transmission device brings along the Central Shaft to drive. The upper part of the shaft connects with the Quincunx Rack, on the frame is loaded with the roller assembly, and forms a swinging pivot. The central shaft does revolve around the central rotation, at the same time it revolves around the grinding rings, and it self also rotates on account of the grinding effect. The shovel system, in the lower part of rollers, is loaded on the lower part of the Quincunx Rack. In the process of rotating of the shovel and the roller, the material will be fed gasket layer between the rollers and ring. The outside centrifugal force (compression force) yielding in this process will process the material into small powder, thus the desired powder is obtained.
Carbon Black Recycling Machine,Continuous Black Oil Recycling Machine,Oil Recycling Machine,Waste Oil Recycling Machine Henan Lanning Technology Co., Ltd , https://www.lanningrecycling.com
