XMC HAC5000-10 1'' central pneumatic Air Compressor parts air filter regulator lubricator With Quick Fitting
Specification
Air Compressor Fitting,Pneumatic Air Compressor Fitting,Air Compressors Steel Pipe Fitting,Plastic Air Compressor Fitting Hangzhou Hanray Industry Co., Ltd , https://www.aircompressor.pl
0.05~0.85MPa
Our advantages
1. OEM available.Experienced pneumatic product suppler.
2. Professional design team and sales department for your service.100% test for air pressure and inspection for product appearance before shipment.
3. Alibaba supplier , factory recognized by CE/FSC/ISO9001 and so on.
4. 7/24 Service for you , all the question will be dealt within 24 hours.
5. Location advantage: Nearby Ningbo port, the second largest port in China, convenient transportation and low cost, and close to Shanghai, convenient for customers to visit our factory.
GB7000.1-2015 requirements for LED lamps
With the continuous development of LED technology, many LED products have gradually replaced the market using traditional light source products. China's current national standard for lamps is still GB7000.1-2007 version, this time GB7000.1-2015 (hereinafter referred to as the new version of the standard), added a lot of requirements for the adaptation of LED lamps, which for the certification of China's LED lighting products, international Mutual recognition has played a big role. Nameplate markings Standards for the characteristics of LED luminaires add additional requirements to the nameplate markings of luminaire products that use LEDs as a light source. For example, in the new standard, lamps that can be mounted on the surface of ordinary combustible materials are no longer required to have the F symbol in the mark, which means that the product without warning mark has the highest requirements and the widest range of use, which is very small for some very small LED lamps. The content and space of the mark are saved, but if a product that cannot be covered by the heat insulating material is encountered, the relevant symbols are required to be seen during installation, and each side is at least 25 mm, which is for a small-sized LED recessed light fixture. Say, you need to pay attention. The symbol that the embedded luminaire cannot be covered by the thermal insulation material is different from the ultraviolet radiation of the traditional metal halide lamp. The blue light overflow of the LED luminaire affects the human syllabic rhythm through the human retinal nerve, and even worsens the retina of the minor. . The new standard requires that the luminaire should have a corresponding mark to warn the constructor or user to avoid the risk of blue light hazard. For portable luminaires and hand-held luminaires, if the product has a threshold illuminance Ethr according to IEC/TR 62778 and the distance between the luminaire and the luminaire is above 200mm, the standard believes that the user may approach the luminaire frequently, so it is required When you see the light source, you can see the warning symbol first, reminding the user not to look at the light source that is on; for a fixed installation, if the same threshold illumination is met, a distance must be provided in the manual to inform the constructor. The product should be installed at a distance from the person to avoid passing the person into the area with retinal damage. In addition to some self-ballasted LED bulbs, the LED light source of many luminaires is designed to be non-user-replaceable or even non-replaceable, which leads to the problem of the user not being able to identify whether the luminaire can be replaced during use. When a lamp is at the end of its life, or when it is faulty, the user often cannot recognize the state of the light source of the lamp from outside the lamp. This causes the user to open the lamp cover and find out if there is a live part inside the lamp, which may cause electric shock. . Different from the traditional light source connection form, it usually has a standard lamp holder component, which may be E14, E27, 2G11, G5, G13, G12, etc. Even if the lampshade is turned on and the light source is replaced by hand, it also has certain protection against electric shock. Non-user replacement or non-replaceable LED light source connection methods generally do not use standard lamp holders, but use some connectors, even direct soldering, when there is no standard parts to provide protection against electric shock, it is very necessary to inform users of the danger of electric shock, The new version of the standard requires warnings and warning signs of electric shock (IEC 60417-6042). Electrical Insulation Most LED modules operate under DC conditions, which is different from the working conditions of conventional light sources. Obviously, the electrical insulation properties of LED lamps will also change. The new version of the standard is mainly adapted to the creepage distance clearance, electrical strength and related structural requirements to adapt to this change. The new version of the standard has a tendency to relax the creepage distance and clearance requirements of the luminaire. Firstly, it does not distinguish between ordinary luminaires and non-ordinary luminaires (IPX1 and above). It is considered that as long as the enclosure protection can pass, the fixture cavity is equivalent to the IP20 environment. At the same time, the creepage distance and clearance under DC voltage are clearly defined: for the creepage distance, the equivalent DC voltage is equal to the effective value of the sinusoidal AC voltage. For the clearance, the equivalent DC voltage is equal to the peak value of the AC voltage. . This means that the limit of creepage distance can be directly calculated by considering the DC voltage as the AC rms value, and the gap has a peak and RMS conversion. With the reduction of creepage distance clearance requirements, the voltage value of the electrical strength test also shows a downward trend. The additional insulation is reduced to the equivalent of 2U+1000 for basic insulation, and the double insulation or reinforced insulation is reduced to 4U+2000. Some small-volume LED luminaires have limited space inside, the inter-electrode spacing, and the distance between the pole and the shell are small due to With the relaxation of this clause, such luminaires are undoubtedly easier to pass the test. LED luminaires also have programmable features that can be closely related to smart lighting. Therefore, LED luminaires have many control lines, dimming lines, etc. compared to conventional luminaires. The new standard also increases the insulation requirements between various types of lines, such as SELV. Between the circuit and the LV power supply, between the SELV circuit and the FELV circuit. For details, refer to Appendix X of the standard, which specifies the insulation requirements for active components and accessible conductive components of circuits in various types of luminaires.
Order No.
HAC5000-10
Ensured Pressure Resistance
1.5MPa (15kgf/cm2)
Highest Working Pressure
1.0MPa (10kgf/cm2)
Ambient and Fluid Temperature
5~60℃
*Filter Precision
25μm
Recommended Oil Use
Turbine No.1 Oil ISOVG32
Container Material
Polycarbonate
Protective Cover
Available
Pressure Regulating Range
Valve Type
With Overflow